Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
Listed here below you can get some high-quality points involving Installing A Bathtub.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall to remove the old bathtub and position the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. See to it you have certified on your own for the task and also are comfortable trying it. Rather than employing a specialist to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a new bath tub in your shower room if you have already bought a new bathtub as well as don't need to alter the setup of your previous supply of water pipes.
Your tools and also material list need to comprise the following:
Preparing for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to prevent stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of removing the existing faucets can be quite problematic due to the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bath tub in the required setting. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub till the level reads level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water supply and also check all joints and new pipework for leakages and tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bath paneling as described in the supplier's user's manual. Tiling and also sealing around the bathtub must wait up until the bath tub has been used at the very least when as this will settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and also the sink. Secure the faucet in position with the maker offered backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind must be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about problems with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and installations. They are offered in tubes as well as cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealant can split relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that blog posting about Installing A Bathtub while doing a search on the internet. If you enjoyed reading our blog post kindly do not forget to pass it around. Thanks a lot for your time invested reading it.
Get Quote Now
Report this page